Cudy AP3000 v1

The Cudy AP3000 v1 is an Indoor Wifi6 Ceiling / Wall Access Point with 1x 2.5GB LAN Port. It has 2 antennas for the 2.4GHz band and 3 antennas for the 5GHz band. The Power Option includes 12V DC (1.5A), 802.3at (PoE+) as well as passive PoE.

None at this time.

See OEM easy installation for a guide on how to install OpenWrt after unboxing the device

root@OpenWrt:/# cat /proc/mtd
dev:    size   erasesize  name
mtd0: 00100000 00020000 "bl2"
mtd1: 00080000 00020000 "u-boot-env"
mtd2: 00200000 00020000 "factory"
mtd3: 00040000 00020000 "bdinfo"
mtd4: 00200000 00020000 "fip"
mtd5: 04000000 00020000 "ubi"

Note: Reset router to factory defaults if it has been previously configured.

1. Download the appropriate Cudy-signed OpenWrt image from Cudy's Google Disk or ask the Cudy Support to send you the file
2. Download the latest OpenWrt stable sysupgrade image
3. Browse to http://192.168.10.254/
4. Choose a password. This won't be needed later
5. Navigate to http://192.168.10.254/cgi-bin/luci/admin/panel
6. Click on the Firmware button
7. Upload the Cudy-signed OpenWrt image
8. Click on the proceed button
9. Wait for the device to reboot
10. SSH to 192.168.1.1 or browse to http://192.168.1.1
11. Flash the latest OpenWrt stable sysupgrade image

Entering the TFTP mode, which is currently inoperable, can be done by pressing and holding the reset button and then connecting the device to power. Release the button when the LED blinks orange and red.

TFTP Installation is not working due to a bug but might be available in the future. The TFTP Server is running but it is not possible to get an ethernet link. Looking at the serial console you can see this:

ethernet@15100000 Waiting for PHY auto negotiation to complete......... TIMEOUT !
MT7981>

U-Boot env info:

MT7981> env print
baudrate=115200
bootdelay=2
ethact=ethernet@15100000
ethaddr=fe:b8:08:27:1d:6d
fdtcontroladdr=5ffc3a00
ipaddr=192.168.1.112
loadaddr=0x46000000
netmask=255.255.255.0
serverip=192.168.1.88
stderr=serial@11002000
stdin=serial@11002000
stdout=serial@11002000

Environment size: 257/131068 bytes

→ generic.sysupgrade

→ generic.debrick

The failsafe mode has the limitation of only working with IPv6. You need to find out the IPv6 link-local address of your specific device in order to reach it. IPv4 is not working, likely due to a bug, as there is no IPv4 address set on the lan interface when in failsafe mode

→ failsafe_and_factory_reset

→ Basic configuration After flashing, proceed with this.
Set up your Internet connection, configure wireless, configure USB port, etc.

The default network configuration is:

The device has no switch ports

→ hardware.button on howto use and configure the hardware button(s).

The Cudy AP3000 has the following buttons:

---- datatemplatelist dttpllist ---- template: meta:template_datatemplatelist cols : Brand, Model, Versions, Device Type, Availability, Supported Since Commit_git, Supported since Rel, Supported current Rel, Unsupported, Bootloader, CPU, Target, CPU MHz, Flash MBs, RAM MB, Switch, Ethernet 100M ports_, Ethernet Gbit ports_, Comments network ports_, Modem, VLAN, WLAN 2.4GHz, WLAN 5.0GHz, WLAN Hardwares, WLAN Comments_, Detachable Antennas_, USB ports_, SATA ports_, Comments USB SATA ports_, Serial, JTAG, LED count, Button count, Power supply, Device Techdata_pageid, Forum topic URL_url, wikidevi URL_url, OEM Device Homepage URL_url, Firmware OEM Stock URL_url, Firmware OpenWrt Install URL_url, Firmware OpenWrt Upgrade URL_url, Comments_ filter : Brand=Cudy filter : Model=AP3000 filter : Versions=v1

Front view of the device:

Bottom of the device including the ports:

Device Label:

Front of PCB with heatsink:

Front of PCB without heatsink:

Back of PCB with shield:

Back of PCB without shield:

→ Warranty

To open the device unscrew the two cross screws at the bottom of the device. The top case is clipped in so you can use a flat tool get in between the top and the main case and lift the top case up.

Device with case openend:

→ port.serial general information about the serial port, serial port cable, etc.

How to connect to the Serial Port of this specific device:
The pins are located on the top of the PCB under the heatsink. You need to remove the heatsink in order to reach the pins.

F0: 102B 0000
FA: 1040 0000
FA: 1040 0000 [0200]
F9: 0000 0000
V0: 0000 0000 [0001]
00: 0000 0000
BP: 2400 0041 [0000]
G0: 1190 0000
EC: 0000 0000 [1000]
T0: 0000 024B [010F]
Jump to BL

NOTICE:  BL2: v2.7(release):ba36282065
NOTICE:  BL2: Built : 07:22:10, Sep 10 2024
NOTICE:  WDT: disabled
NOTICE:  EMI: Using DDR4 settings

dump toprgu registers data: 
1001c000 | 00000000 0000ffe0 00000000 00000000
1001c010 | 00000fff 00000000 00f00000 00000000
1001c020 | 00000000 00000000 00000000 00000000
1001c030 | 003c0003 003c0003 00000000 00000000
1001c040 | 00000000 00000000 00000000 00000000
1001c050 | 00000000 00000000 00000000 00000000
1001c060 | 00000000 00000000 00000000 00000000
1001c070 | 00000000 00000000 00000000 00000000
1001c080 | 00000000 00000000 00000000 00000000

dump drm registers data: 
1001d000 | 00000000 00000000 00000000 00000000
1001d010 | 00000000 00000000 00000000 00000000
1001d020 | 00000000 00000000 00000000 00000000
1001d030 | 00a083f1 000003ff 00100000 00000000
1001d040 | 00000000 00000000 00020303 000000ff
1001d050 | 00000000 00000000 00000000 00000000
1001d060 | 00000002 00000000 00000000 00000000
drm: 500 = 0x8 
[DDR Reserve] ddr reserve mode not be enabled yet
DDR RESERVE Success 0
[EMI] ComboMCP not ready, using default setting
BYTE_swap:0 
BYTE_swap:0 
Window Sum 548, worse bit 1, min window 64
Window Sum 552, worse bit 8, min window 68
[TxChooseVref] Worse bit 1, Min win 24, Win sum 405, Final Vref 40
Window Sum 310, worse bit 3, min window 34
Window Sum 314, worse bit 8, min window 36
Window Sum 336, worse bit 1, min window 38
Window Sum 328, worse bit 8, min window 38
Window Sum 348, worse bit 3, min window 38
Window Sum 344, worse bit 8, min window 40
Window Sum 360, worse bit 1, min window 42
Window Sum 360, worse bit 10, min window 42
Window Sum 376, worse bit 1, min window 44
Window Sum 376, worse bit 10, min window 44
Window Sum 382, worse bit 3, min window 44
Window Sum 388, worse bit 10, min window 44
Window Sum 392, worse bit 3, min window 44
Window Sum 396, worse bit 10, min window 46
Window Sum 404, worse bit 3, min window 46
Window Sum 414, worse bit 10, min window 50
Window Sum 414, worse bit 1, min window 48
Window Sum 422, worse bit 3, min window 48
Window Sum 434, worse bit 11, min window 50
Window Sum 436, worse bit 3, min window 50
Window Sum 444, worse bit 11, min window 52
Window Sum 440, worse bit 1, min window 52
Window Sum 450, worse bit 3, min window 52
Window Sum 458, worse bit 10, min window 54
Window Sum 458, worse bit 3, min window 54
Window Sum 466, worse bit 15, min window 54
Window Sum 462, worse bit 3, min window 54
Window Sum 466, worse bit 10, min window 56
Window Sum 474, worse bit 1, min window 56
Window Sum 482, worse bit 10, min window 58
Window Sum 478, worse bit 1, min window 58
Window Sum 486, worse bit 11, min window 58
Window Sum 490, worse bit 11, min window 58
Window Sum 486, worse bit 3, min window 58
Window Sum 496, worse bit 9, min window 60
NOTICE:  EMI: Detected DRAM size: 512MB
NOTICE:  EMI: complex R/W mem test passed
NOTICE:  CPU: MT7981 (1300MHz)
NOTICE:  SPI_NAND parses attributes from parameter page.
NOTICE:  SPI_NAND Detected ID 0x2c
NOTICE:  Page size 2048, Block size 131072, size 268435456
NOTICE:  Initializing NMBM ...
NOTICE:  Signature found at block 2047 [0x0ffe0000]
NOTICE:  First info table with writecount 0 found in block 1920
NOTICE:  Second info table with writecount 0 found in block 1923
NOTICE:  NMBM has been successfully attached in read-only mode
NOTICE:  BL2: Booting BL31
NOTICE:  BL31: v2.7(release):ba36282065
NOTICE:  BL31: Built : 07:22:10, Sep 10 2024
NOTICE:  Hello BL31!!!


U-Boot 2022.07-rc3 (Sep 10 2024 - 07:22:10 +0000), Build: jenkins-AP3000-22

CPU:   MediaTek MT7981
Model: mt7981-rfb
DRAM:  512 MiB
Core:  44 devices, 20 uclasses, devicetree: embed

Initializing NMBM ...
spi-nand: spi_nand spi_nand@0: Micron SPI NAND was found.
spi-nand: spi_nand spi_nand@0: 256 MiB, block size: 128 KiB, page size: 2048, OOB size: 128
Could not find a valid device for nmbm0
Signature found at block 2047 [0x0ffe0000]
First info table with writecount 0 found in block 1920
Second info table with writecount 0 found in block 1923
NMBM has been successfully attached 

Loading Environment from MTD... *** Warning - bad CRC, using default environment

In:    serial@11002000
Out:   serial@11002000
Err:   serial@11002000
Net:   
Warning: ethernet@15100000 (eth0) using random MAC address - 02:8a:9d:8c:37:da
eth0: ethernet@15100000
gpio: pin 39 (gpio 39) value is 0
ubi0: attaching mtd7
ubi0: scanning is finished
ubi0: attached mtd7 (name "ubi", size 64 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
ubi0: good PEBs: 512, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 3/2, WL threshold: 4096, image sequence number: 1922569072
ubi0: available PEBs: 4, total reserved PEBs: 508, PEBs reserved for bad PEB handling: 38
Reading from volume 'kernel' to 0x46000000, size 0x0 ... OK
## Loading kernel from FIT Image at 46000000 ...
   Using 'config-1' configuration
   Trying 'kernel-1' kernel subimage
     Description:  ARM64 OpenWrt Linux-6.6.110
     Type:         Kernel Image
     Compression:  lzma compressed
     Data Start:   0x460000e8
     Data Size:    4132682 Bytes = 3.9 MiB
     Architecture: AArch64
     OS:           Linux
     Load Address: 0x48000000
     Entry Point:  0x48000000
     Hash algo:    crc32
     Hash value:   5bfad146
     Hash algo:    sha1
     Hash value:   7e7b62b9716fb07c6a68836f399014fbcdf3ad87
   Verifying Hash Integrity ... crc32+ sha1+ OK
## Loading fdt from FIT Image at 46000000 ...
   Using 'config-1' configuration
   Trying 'fdt-1' fdt subimage
     Description:  ARM64 OpenWrt cudy_ap3000-v1 device tree blob
     Type:         Flat Device Tree
     Compression:  uncompressed
     Data Start:   0x463f1174
     Data Size:    22348 Bytes = 21.8 KiB
     Architecture: AArch64
     Hash algo:    crc32
     Hash value:   cf1a40f6
     Hash algo:    sha1
     Hash value:   1d0c56bcb17fda0fd9b4d7425d03b2c528e8c479
   Verifying Hash Integrity ... crc32+ sha1+ OK
   Booting using the fdt blob at 0x463f1174
   Uncompressing Kernel Image
   Loading Device Tree to 000000005f7f0000, end 000000005f7f874b ... OK

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
[    0.000000] Linux version 6.6.110 (builder@buildhost) (aarch64-openwrt-linux-musl-gcc (OpenWrt GCC 13.3.0 r28959-29397011cc) 13.3.0, GNU ld (GNU Binutils) 2.42) #0 SMP Sun Oct 19 16:37:45 2025
[    0.000000] Machine model: Cudy AP3000 v1
[    0.000000] OF: reserved mem: 0x0000000042ff0000..0x0000000042ffffff (64 KiB) map non-reusable ramoops@42ff0000
[    0.000000] OF: reserved mem: 0x0000000043000000..0x000000004302ffff (192 KiB) nomap non-reusable secmon@43000000
[    0.000000] OF: reserved mem: 0x0000000047c80000..0x0000000047d7ffff (1024 KiB) nomap non-reusable wmcpu-reserved@47c80000
[    0.000000] OF: reserved mem: 0x0000000047d80000..0x0000000047dbffff (256 KiB) nomap non-reusable wo-emi@47d80000
[    0.000000] OF: reserved mem: 0x0000000047dc0000..0x0000000047ffffff (2304 KiB) nomap non-reusable wo-data@47dc0000
[    0.000000] Zone ranges:
[    0.000000]   DMA      [mem 0x0000000040000000-0x000000005fffffff]
[    0.000000]   DMA32    empty
[    0.000000]   Normal   empty
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000040000000-0x0000000042ffffff]
[    0.000000]   node   0: [mem 0x0000000043000000-0x000000004302ffff]
[    0.000000]   node   0: [mem 0x0000000043030000-0x0000000047c7ffff]
[    0.000000]   node   0: [mem 0x0000000047c80000-0x0000000047ffffff]
[    0.000000]   node   0: [mem 0x0000000048000000-0x000000005fffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x000000005fffffff]
[    0.000000] psci: probing for conduit method from DT.
[    0.000000] psci: PSCIv1.1 detected in firmware.
[    0.000000] psci: Using standard PSCI v0.2 function IDs
[    0.000000] psci: MIGRATE_INFO_TYPE not supported.
[    0.000000] psci: SMC Calling Convention v1.2
[    0.000000] percpu: Embedded 18 pages/cpu s35624 r8192 d29912 u73728
[    0.000000] pcpu-alloc: s35624 r8192 d29912 u73728 alloc=18*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 
[    0.000000] Detected VIPT I-cache on CPU0
[    0.000000] CPU features: detected: GIC system register CPU interface
[    0.000000] CPU features: kernel page table isolation disabled by kernel configuration
[    0.000000] alternatives: applying boot alternatives
[    0.000000] Kernel command line: 
[    0.000000] Dentry cache hash table entries: 65536 (order: 7, 524288 bytes, linear)
[    0.000000] Inode-cache hash table entries: 32768 (order: 6, 262144 bytes, linear)
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 129024
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] software IO TLB: SWIOTLB bounce buffer size adjusted to 0MB
[    0.000000] software IO TLB: area num 2.
[    0.000000] software IO TLB: mapped [mem 0x000000005fd69000-0x000000005fde9000] (0MB)
[    0.000000] Memory: 496980K/524288K available (9088K kernel code, 1000K rwdata, 1676K rodata, 448K init, 307K bss, 27308K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] rcu: Hierarchical RCU implementation.
[    0.000000] rcu:     RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[    0.000000]  Tracing variant of Tasks RCU enabled.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[    0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[    0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[    0.000000] GICv3: GIC: Using split EOI/Deactivate mode
[    0.000000] GICv3: 640 SPIs implemented
[    0.000000] GICv3: 0 Extended SPIs implemented
[    0.000000] Root IRQ handler: 0xffffffc080010080
[    0.000000] GICv3: GICv3 features: 16 PPIs
[    0.000000] GICv3: CPU0: found redistributor 0 region 0:0x000000000c080000
[    0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[    0.000000] arch_timer: cp15 timer(s) running at 13.00MHz (phys).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2ff89eacb, max_idle_ns: 440795202429 ns
[    0.000000] sched_clock: 56 bits at 13MHz, resolution 76ns, wraps every 4398046511101ns
[    0.000076] Calibrating delay loop (skipped), value calculated using timer frequency.. 26.00 BogoMIPS (lpj=130000)
[    0.000084] pid_max: default: 32768 minimum: 301
[    0.002956] Mount-cache hash table entries: 1024 (order: 1, 8192 bytes, linear)
[    0.002966] Mountpoint-cache hash table entries: 1024 (order: 1, 8192 bytes, linear)
[    0.005133] cacheinfo: Unable to detect cache hierarchy for CPU 0
[    0.005676] RCU Tasks Trace: Setting shift to 1 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=2.
[    0.005820] rcu: Hierarchical SRCU implementation.
[    0.005824] rcu:     Max phase no-delay instances is 1000.
[    0.006210] smp: Bringing up secondary CPUs ...
[    0.006572] Detected VIPT I-cache on CPU1
[    0.006616] GICv3: CPU1: found redistributor 1 region 0:0x000000000c0a0000
[    0.006645] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
[    0.006716] smp: Brought up 1 node, 2 CPUs
[    0.006722] SMP: Total of 2 processors activated.
[    0.006726] CPU features: detected: 32-bit EL0 Support
[    0.006729] CPU features: detected: CRC32 instructions
[    0.006761] CPU features: emulated: Privileged Access Never (PAN) using TTBR0_EL1 switching
[    0.006764] CPU: All CPU(s) started at EL2
[    0.006766] alternatives: applying system-wide alternatives
[    0.010304] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.010321] futex hash table entries: 512 (order: 3, 32768 bytes, linear)
[    0.011580] pinctrl core: initialized pinctrl subsystem
[    0.012727] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[    0.013061] DMA: preallocated 128 KiB GFP_KERNEL pool for atomic allocations
[    0.013086] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
[    0.013107] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
[    0.013491] thermal_sys: Registered thermal governor 'fair_share'
[    0.013494] thermal_sys: Registered thermal governor 'bang_bang'
[    0.013497] thermal_sys: Registered thermal governor 'step_wise'
[    0.013499] thermal_sys: Registered thermal governor 'user_space'
[    0.013538] ASID allocator initialised with 65536 entries
[    0.014451] pstore: Using crash dump compression: deflate
[    0.014456] pstore: Registered ramoops as persistent store backend
[    0.014459] ramoops: using 0x10000@0x42ff0000, ecc: 0
[    0.015822] /soc/interrupt-controller@c000000: Fixed dependency cycle(s) with /soc/interrupt-controller@c000000
[    0.021481] Modules: 29600 pages in range for non-PLT usage
[    0.021489] Modules: 521120 pages in range for PLT usage
[    0.022595] cryptd: max_cpu_qlen set to 1000
[    0.023690] SCSI subsystem initialized
[    0.023883] libata version 3.00 loaded.
[    0.025670] clocksource: Switched to clocksource arch_sys_counter
[    0.027946] NET: Registered PF_INET protocol family
[    0.028063] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear)
[    0.029469] tcp_listen_portaddr_hash hash table entries: 256 (order: 0, 4096 bytes, linear)
[    0.029483] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[    0.029493] TCP established hash table entries: 4096 (order: 3, 32768 bytes, linear)
[    0.029526] TCP bind hash table entries: 4096 (order: 5, 131072 bytes, linear)
[    0.029625] TCP: Hash tables configured (established 4096 bind 4096)
[    0.029946] MPTCP token hash table entries: 512 (order: 1, 12288 bytes, linear)
[    0.030153] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[    0.030171] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[    0.030390] NET: Registered PF_UNIX/PF_LOCAL protocol family
[    0.030415] PCI: CLS 0 bytes, default 64
[    0.031652] workingset: timestamp_bits=46 max_order=17 bucket_order=0
[    0.036486] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.036495] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.094004] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
[    0.104704] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    0.108497] printk: console [ttyS0] disabled
[    0.128894] 11002000.serial: ttyS0 at MMIO 0x11002000 (irq = 72, base_baud = 2500000) is a ST16650V2
[    0.128937] printk: console [ttyS0] enabled
[    0.885255] loop: module loaded
[    0.891515] spi-nand spi0.0: calibration result: 0x2
[    0.896648] spi-nand spi0.0: Micron SPI NAND was found.
[    0.901865] spi-nand spi0.0: 256 MiB, block size: 128 KiB, page size: 2048, OOB size: 128
[    0.910388] Signature found at block 2047 [0x0ffe0000]
[    0.915516] NMBM management region starts at block 1920 [0x0f000000]
[    0.923238] First info table with writecount 0 found in block 1920
[    0.932718] Second info table with writecount 0 found in block 1923
[    0.939001] NMBM has been successfully attached
[    0.943870] 6 fixed-partitions partitions found on MTD device spi0.0
[    0.950242] Creating 6 MTD partitions on "spi0.0":
[    0.955023] 0x000000000000-0x000000100000 : "bl2"
[    0.960674] 0x000000100000-0x000000180000 : "u-boot-env"
[    0.966755] 0x000000180000-0x000000380000 : "factory"
[    0.973513] 0x000000380000-0x0000003c0000 : "bdinfo"
[    0.979392] 0x0000003c0000-0x0000005c0000 : "fip"
[    0.985600] 0x0000005c0000-0x0000045c0000 : "ubi"
[    1.530074] mtk_soc_eth 15100000.ethernet eth0: mediatek frame engine at 0xffffffc081700000, irq 75
[    1.539838] i2c_dev: i2c /dev entries driver
[    1.545951] mtk-wdt 1001c000.watchdog: Watchdog enabled (timeout=31 sec, nowayout=0)
[    1.555095] NET: Registered PF_INET6 protocol family
[    1.561154] Segment Routing with IPv6
[    1.564853] In-situ OAM (IOAM) with IPv6
[    1.568843] NET: Registered PF_PACKET protocol family
[    1.573919] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[    1.587129] 8021q: 802.1Q VLAN Support v1.8
[    1.617360] UBI: auto-attach mtd5
[    1.620685] ubi0: default fastmap pool size: 25
[    1.625205] ubi0: default fastmap WL pool size: 12
[    1.630004] ubi0: attaching mtd5
[    1.813710] ubi0: scanning is finished
[    1.822562] ubi0: attached mtd5 (name "ubi", size 64 MiB)
[    1.827984] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    1.834847] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    1.841624] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[    1.848579] ubi0: good PEBs: 512, bad PEBs: 0, corrupted PEBs: 0
[    1.854573] ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128
[    1.861787] ubi0: max/mean erase counter: 3/2, WL threshold: 4096, image sequence number: 1922569072
[    1.870907] ubi0: available PEBs: 2, total reserved PEBs: 510, PEBs reserved for bad PEB handling: 38
[    1.880124] ubi0: background thread "ubi_bgt0d" started, PID 572
[    1.880858] block ubiblock0_1: created from ubi0:1(rootfs)
[    1.891619] ubiblock: device ubiblock0_1 (rootfs) set to be root filesystem
[    1.898698] clk: Disabling unused clocks
[    1.907687] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[    1.914982] Freeing unused kernel memory: 448K
[    1.919553] Run /sbin/init as init process
[    1.923642]   with arguments:
[    1.926614]     /sbin/init
[    1.929309]   with environment:
[    1.932437]     HOME=/
[    1.934785]     TERM=linux
[    2.128798] init: Console is alive
[    2.132365] init: - watchdog -
[    2.469120] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    2.495728] gpio_button_hotplug: loading out-of-tree module taints kernel.
[    2.505473] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    2.523037] init: - preinit -
[    3.075748] mtk_soc_eth 15100000.ethernet eth0: PHY [mdio-bus:01] driver [RTL8221B-VB-CG 2.5Gbps PHY (C45)] (irq=53)
[    3.089839] mtk_soc_eth 15100000.ethernet eth0: configuring for phy/2500base-x link mode
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[    7.325700] random: crng init done
[    7.332403] UBIFS (ubi0:2): Mounting in unauthenticated mode
[    7.338177] UBIFS (ubi0:2): background thread "ubifs_bgt0_2" started, PID 703
[    7.359285] UBIFS (ubi0:2): recovery needed
[    7.431072] UBIFS (ubi0:2): recovery completed
[    7.435583] UBIFS (ubi0:2): UBIFS: mounted UBI device 0, volume 2, name "rootfs_data"
[    7.443427] UBIFS (ubi0:2): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[    7.453332] UBIFS (ubi0:2): FS size: 48885760 bytes (46 MiB, 385 LEBs), max 395 LEBs, journal size 2412544 bytes (2 MiB, 19 LEBs)
[    7.464971] UBIFS (ubi0:2): reserved for root: 2308995 bytes (2254 KiB)
[    7.471577] UBIFS (ubi0:2): media format: w5/r0 (latest is w5/r0), UUID 64A3D40C-4D50-4430-BFA2-A27BCA614DA4, small LPT model
[    7.485417] mount_root: switching to ubifs overlay
[    7.493393] overlayfs: null uuid detected in lower fs '/', falling back to xino=off,index=off,nfs_export=off.
[    7.507388] urandom-seed: Seeding with /etc/urandom.seed
[    7.552890] procd: - early -
[    7.555898] procd: - watchdog -
[    8.102713] procd: - watchdog -
[    8.152653] procd: - ubus -
[    8.307008] procd: - init -
Please press Enter to activate this console.
[    8.669276] kmodloader: loading kernel modules from /etc/modules.d/*
[    8.708065] crypto-safexcel 10320000.crypto: EIP97:230(0,1,4,4)-HIA:270(0,5,5),PE:150/433(alg:7fcdfc00)/0/0/0
[    8.725455] Loading modules backported from Linux version v6.12.52-0-g2b2cbdcede38
[    8.733070] Backport generated by backports.git v6.1.110-1-35-g410656ef
[    8.855346] urngd: v1.0.2 started.
[    9.109429] mt798x-wmac 18000000.wifi: HW/SW Version: 0x8a108a10, Build Time: 20240823161240a
[    9.109429] 
[    9.303225] mt798x-wmac 18000000.wifi: WM Firmware Version: ____000000, Build Time: 20240823161304
[    9.397393] mt798x-wmac 18000000.wifi: WA Firmware Version: DEV_000000, Build Time: 20240823161841
[    9.494955] mt798x-wmac 18000000.wifi: registering led 'mt76-phy0'
[    9.577341] mt798x-wmac 18000000.wifi: registering led 'mt76-phy1'
[    9.684912] mtdblock: MTD device 'bdinfo' is NAND, please consider using UBI block devices instead.
[    9.696929] PPP generic driver version 2.4.2
[    9.702388] NET: Registered PF_PPPOX protocol family
[    9.711346] kmodloader: done loading kernel modules from /etc/modules.d/*
[    9.947210] mtdblock: MTD device 'bdinfo' is NAND, please consider using UBI block devices instead.
[   13.436063] mtk_soc_eth 15100000.ethernet eth0: PHY [mdio-bus:01] driver [RTL8221B-VB-CG 2.5Gbps PHY (C45)] (irq=53)
[   13.450366] mtk_soc_eth 15100000.ethernet eth0: configuring for phy/2500base-x link mode
[   13.496392] br-lan: port 1(eth0) entered blocking state
[   13.501626] br-lan: port 1(eth0) entered disabled state
[   13.506902] mtk_soc_eth 15100000.ethernet eth0: entered allmulticast mode
[   13.513834] mtk_soc_eth 15100000.ethernet eth0: entered promiscuous mode

U-boot 2core ARMv8 mediatek filogic MT7981BA 128NAND 256RAM 5port GigabitEthernet 802.11ax serial 1NIC 2.5GigabitEthernet no switch InternalAntenna 5Ant 0USB 12v powered PoE ceiling